注塑機鑄鋁電加熱器

注塑機鑄鋁電加熱器概述：

注塑機鑄鋁電加熱器是以管狀電熱元件為發熱體，并彎曲成型，用優良鑄材料為外殼，外殼以離心式澆鑄成各種形狀的電加熱器，有圓型、平板、直角型、風冷、水冷及其它異型等。經精加工后它能和被加熱體緊密貼合。其使用溫度一般在攝氏150～450度之間，可廣泛應用于塑料機械、模頭、電纜機械、化工、橡膠、石油等設備上。

注塑機鑄鋁電加熱器注意事項：

1.金屬鑄造加熱器應放在干燥處、若因長期放置，絕緣電阻低于1MΩ時，可在攝氏200度左右的烘箱中烘烤5-6小時，即可恢復正常。或降低電壓通電加熱，直至恢復絕緣電阻。

2.金屬鑄造加熱器應做好定位固定,有效發熱區須與受熱體緊密貼合，嚴禁空燒。發現表面有灰塵或污染物時，應及時處理干凈再用，以免影晌散熱而縮短使用壽命。

3.工作電壓不得超過額定值的10%；空氣相對濕度不大于95%，無爆炸性和腐蝕性氣體。

4.接線部分放在加熱層、保溫層以外，外殼應有效接地；避免與腐蝕性、爆炸性介質、水份接觸;引接線應能長期承受接線部分的溫度及加熱負載，接線螺絲緊固時應避免用力過猛。

5.電熱管出線端的氧化鎂粉，在使用場所避免受到污染物與水分滲入，防止漏電事故的發生。

注塑機鑄鋁電加熱器用途及特點 ： 

主要用于塑料擠出機的料筒加熱裝置上，具有結構合理，外形美觀，性能穩定，加熱快、散熱均勻，絕緣性能良好，耐高壓特點。尤其適用于高溫度高功率的要求上。廣泛運用于注塑機和擠出機、包裝印刷、石油化工、電子設備等行業。

注塑機鑄鋁電加熱器的溫度控制

一般以測溫熱電偶為測溫元件，配以測溫毫伏計成為控溫裝置，指揮料筒和模具鑄鋁電加熱器電流的通斷，有選擇地固定料筒各段溫度和模具溫度。 料筒鑄鋁電加熱器一般分為二段、三段或四段控制。電器柜上的電流表分別顯示各段鑄鋁電加熱器電流的大小。電流表的讀數是比較固定的，如果在運行中發現電流表讀數比較長時間的偏低，則可能鑄鋁電加熱器發生了故障，或導線接觸不良，或電熱絲氧化變細，或某個鑄鋁電加熱器燒毀，這些都將使電路并聯的電阻阻值增大而使電流下降。 在電流表有讀數時也可以簡單地用塑料條逐個在鑄鋁電加熱器外壁上抹劃，看料條熔融與否來判斷某個鑄鋁電加熱器是否通電或燒毀。

注塑機鑄鋁電加熱器技術參數 ：

1、鑄鋁電加熱器表面負荷可達到2.5-4.5w/cm2，高工作溫度300-450℃之間；

2、金屬鑄造加熱器是一種有效熱分部均勻的加熱器，熱導性較佳的金屬合金，確保熱面溫度均勻，消除了設備的熱點及冷點。具有長壽命、保溫性能好、機械性能強、耐腐蝕、抗磁場等優點。將外散熱面增加保溫裝置，內散熱面燒結紅外線這樣可節約用電35%。

3、工作溫度下的泄漏電流和電氣強度。 a)泄漏電流(0.5mA b)電氣強度：1250V1min無閃絡擊穿現象 

4、耐潮濕。 在20∽30℃溫度，空氣相對濕度為91%∽95%的潮濕箱內放置48h，無任何損傷。

5、引出管抗拉性。 承受該零件抗拉力的70%，歷時3min無位移和斷裂現象。

6、功率的偏離率(±5%。5、承受高壓1500v